Tayda 1590DD enclosure dimensions

Wall thickness, casting taper and a free drill template

External, at the rim
190.5 × 121.5 × 33mm

7.50 × 4.78 × 1.30 in

Drilled face
187.3 × 118.3mm

the face you lay out

Usable flat area
174.1 × 105.1mm

inside the walls and bosses

Wall thickness
2.2mm

1.6 mm draft per side

Lay out a 1590DD →

Free in your browser, and it prints a true-size drill template.

Tayda's 1590DD is its own casting rather than a relabelled Hammond, and we carry measured figures for both.

It is the widest of the pair by a millimetre and a half, at the same depth, with thinner walls. The extra goes into the cavity, so a board that just misses in a Hammond may clear here.

1590DD drawing

AABB SECTION A-ASECTION B-B 187.3118.3R5R4.4 BOSS33190.5 AT RIM2.2 WALL1.6 DRAFT(33) NOTES1.MATERIAL: DIE-CAST ALUMINIUM ALLOY2.INTERNAL CAVITY 182.9 x 113.9 AT THEDRILLED FACE3.USABLE FLAT AREA 174.1 x 105.1INSIDE THE CORNER BOSSES4.HIDDEN LINES ARE THE INSIDE FACE OFTHE WALL AND THE CORNER BOSS KEEPOUT5.CASTING DRAFT DRAWN AT TRUE SCALE6.TOP EDGE ROLLOVER SHOWNINDICATIVELY, NOT DIMENSIONED HAMMOND 1590DDDIMENSIONS IN MMSCALE: TO FITSOURCE: HAMMOND CADSTOMPBOXLAYOUT.COMTHIRD ANGLE
The drilled face, with the inside of the wall and the corner screw bosses as dashed hidden lines, and two sections cut on the centrelines showing the wall and the casting draft. Drawn from Tayda's dimensioned sheet, so it agrees with the figures below it. The top edge is rolled on castings like this one, shown here but not dimensioned. Drag the drawing sideways to see the rest of the sheet.

Full specification

External footprint (at the open rim) 190.5 × 121.5 mm (7.50 × 4.78 in)
Drilled (top) face 187.3 × 118.3 mm (7.37 × 4.66 in)
Depth 33 mm (1.30 in)
Wall thickness 2.2 mm
Wall taper (per side, face to rim) 1.6 mm
Corner radius 5 mm
Screw boss reach (each corner) 4.4 mm
Internal cavity (at the face) 182.9 × 113.9 mm (7.20 × 4.48 in)
Usable flat area (inside the bosses) 174.1 × 105.1 mm (6.85 × 4.14 in)
Material Die-cast aluminium alloy

Figures are read from Tayda's own drawing for this casting, the same data the editor and the comparison tool use. Tayda publishes no CAD, so these are measured from the sheet rather than derived from a model.

How thick are the walls?

The 1590DD's walls are 2.2 mm thick. Like every diecast enclosure it also carries a casting draft: each wall leans out by 1.6 mm from the drilled face to the open rim, so the enclosure measures 190.5 × 121.5 mm at the rim and 187.3 × 118.3 mm across the face you drill. Worth knowing when a part seats against the inside of a wall, and why a caliper reading depends on where you take it.

What fits inside?

The internal cavity measures 182.9 × 113.9 mm at the face, and the screw bosses in each corner reduce the usable flat area for a circuit board to about 174.1 × 105.1 mm. To check a specific board, put its dimensions into the enclosure comparison tool's fit checker, or place the whole layout in the editor, which knows each component's real footprint and warns when something clashes with a wall or a boss.

1590DD drill template

The Stompbox Layout editor has the 1590DD as a built-in preset. Place your holes on it, and it prints a true-size PDF drill template with the enclosure outline, every hole position and a ruler to verify your printer's scale. Free, no download, runs in the browser.

Printed at 100% scale it works as a drilling template: tape it to the enclosure, centre punch each mark, then drill. Our guide to hand drilling a pedal enclosure walks the whole job, bit sizes included.

A 3D printed drill jig sitting over a pedal enclosure.

3D printable drill jig

Nothing to tape down, nothing to slip, and it wraps the sides so the jacks line up. The editor makes one from your own layout, for the exact enclosure you picked, $29.

See the drill jig →

How the 1590DD compares

Enclosure External at the rim Drilled face Depth Usable flat area
1590DD (Tayda) 190.5 × 121.5 mm 187.3 × 118.3 mm 33 mm 174.1 × 105.1 mm
1590DD (Hammond) 188 × 120 mm 185.7 × 117.7 mm 33 mm 171.9 × 103.9 mm

1590DD vs 1590DD

The 1590DD is 1.6 mm narrower and 0.6 mm shorter than the 1590DD. The Tayda is wider outside and thinner walled, which compounds: usefully more usable width than the Hammond at the same depth.

1590DD FAQ

What are the dimensions of a 1590DD enclosure?

A Tayda 1590DD measures 190.5 × 121.5 mm × 33 mm externally at the open rim (7.50 × 4.78 in). The drilled face measures 187.3 × 118.3 mm, and the usable flat area inside the walls and corner screw bosses is about 174.1 × 105.1 mm.

How thick are the walls of a 1590DD?

The 1590DD's walls are 2.2 mm thick, with a casting draft of 1.6 mm per side from the drilled face to the open rim.

Is there a drill template for the 1590DD?

Yes. The free Stompbox Layout editor includes the 1590DD as a preset and prints a true-size PDF drill template of your layout, with a ruler to verify print scale.

Every Tayda size

1590LB

49.3 × 49.3 mm face, 27 mm deep

Dimensions →

1590A

37.8 × 92.2 mm face, 27.8 mm deep

Dimensions →

1590B

59 × 111.3 mm face, 27 mm deep

Dimensions →

125B

64.7 × 119.8 mm face, 35.3 mm deep

Dimensions →

1590BB2

118.3 × 92.6 mm face, 33.3 mm deep

Dimensions →

1032L

249.9 × 65.9 mm face, 48 mm deep

Dimensions →

Or see them drawn to scale, side by side, or start from the common Hammond sizes.

Plan your 1590DD layout

Place the drill holes on a 1590DD in the editor, check everything clears the walls and the screw bosses, then print a true-size PDF drill template. Free, in your browser.

Start designing free →