Kliché Mini Drill Template
PedalPCB · 125B
Template details
- Circuit
- Kliché Mini
- Vendor
- PedalPCB
- Enclosure
- Hammond 125B
- Dimensions
- 63.6 × 119.3 × 35.8 mm
- Layout
- 125B 3-Knob (Type 1)
- Category
- Guitar effect
Export formats
- PDF: print at 1:1 scale
- SVG: vector graphic
About this drill template
Drill template for the PedalPCB Kliché Mini, sized for a Hammond 125B enclosure (63.6 × 119.3 × 35.8 mm). The pre-positioned holes match the PCB's pot footprint exactly, with the footswitch centred below the 3-knob layout. Print at 1:1 scale, tape to the enclosure face, centre-punch, and drill. PCB and parts not included.
PedalPCB description: “Compare to Klon Centaur”
A compact version of PedalPCB's Kliché, compared to the Klon Centaur. It keeps the full Klon recipe: a dual-gang Gain pot, germanium clipping diodes and an on-board charge pump for extra internal headroom.
The familiar Klon thing: a mid-forward clean-to-crunch boost that stacks well in front of an amp on the edge of breakup.
The board includes a 3PDT breakout for easier footswitch wiring. Because of the internal charge pump, power it from a regular 9V supply only.
Build notes
Three-knob layouts give you the full gain / EQ / volume triplet without crowding the enclosure. There's room inside for the PCB, jacks, and a 9V supply.
The Hammond 125B is one of the most common DIY pedal enclosures: a touch larger than a 1590B, slightly smaller than a 1590BB, with room for almost any single-effect PCB plus 9V supply.
Vendor specs: Includes 3PDT breakout board for easier wiring. Designed for a 125B enclosure with top-mounted jacks
Knobs
- Gain
- Volume
- Treble
Drill measurements
Hole centres for the 125B 3-Knob (Type 1) layout. X runs left to right from the centre of the face being drilled. On the enclosure face, Y is measured from the centre, positive towards the top. For holes on a side, Y is the distance down the wall, measured from the face edge. Export the PDF for a 1:1 printable version with a scale check.
| Hole | Face | X (mm) | Y (mm) | Diameter |
|---|---|---|---|---|
| LED | Enclosure face | 0 | 38.1 | 6.4 mm (0.25 in) |
| Pot | Enclosure face | -16.5 | 38.1 | 7 mm (0.28 in) |
| Pot | Enclosure face | 16.5 | 38.1 | 7 mm (0.28 in) |
| Pot | Enclosure face | 0 | 12.7 | 7 mm (0.28 in) |
| Footswitch | Enclosure face | 0 | -45 | 12 mm (0.47 in) |
| DC Jack | Top side | 0 | 14.2 | 8 mm (0.31 in) |
| Jack | Top side | -15.2 | 24.3 | 9.5 mm (0.37 in) |
| Jack | Top side | 15.3 | 24.3 | 9.5 mm (0.37 in) |
Never drilled one before? How to drill a pedal enclosure walks you through the entire process, from punching the centres to the final step drill size.
Print a drill jig for your own build
The editor turns a layout into a jig for the exact enclosure you picked. It fits snugly, so it stays put while you punch and every mark lands where your layout puts it. It marks the side faces as well, so the jacks and the DC socket are covered.
See the drill jig, $29 →