1590BBS 6-Knob 2-Channel 2-Toggle Drill Template
Aion FX · 1590BBS · used by 1 circuit
Template details
- Layout
- 1590BBS 6-Knob 2-Channel 2-Toggle
- Vendor
- Aion FX
- Enclosure
- Hammond 1590BBS
- Dimensions
- 117.8 × 92.3 × 38.1 mm
- Used by
- 1 circuit
Export formats
- PDF: print at 1:1 scale
- SVG: vector graphic
About this layout
The 1590BBS 6-Knob 2-Channel 2-Toggle template positions 17 holes (117.8 × 92.3 × 38.1 mm): 3 × Pot B, 3 × Pot A, Toggle B, Toggle A, Footswitch B, LED B, LED A, Footswitch A on the enclosure face; Output, DC, Input, Loop Return, Loop Send on the top side. Every circuit listed below shares these hole positions, so one printed template covers any of them. Print the PDF at 1:1 scale, tape it to the enclosure, centre-punch, and drill.
Drill measurements
Hole centres for the 1590BBS 6-Knob 2-Channel 2-Toggle layout. X runs left to right from the centre of the face being drilled. On the enclosure face, Y is measured from the centre, positive towards the top. For holes on a side, Y is the distance down the wall, measured from the face edge. Export the PDF for a 1:1 printable version with a scale check.
| Hole | Face | X (mm) | Y (mm) | Diameter |
|---|---|---|---|---|
| Pot B | Enclosure face | -43.7 | 29 | 7 mm (0.28 in) |
| Pot B | Enclosure face | -14.7 | 29 | 7 mm (0.28 in) |
| Pot A | Enclosure face | 14.7 | 29 | 7 mm (0.28 in) |
| Pot A | Enclosure face | 43.7 | 29 | 7 mm (0.28 in) |
| Pot B | Enclosure face | -43.7 | 0 | 7 mm (0.28 in) |
| Toggle B | Enclosure face | -14.7 | 0 | 6 mm (0.24 in) |
| Toggle A | Enclosure face | 14.7 | 0 | 6 mm (0.24 in) |
| Pot A | Enclosure face | 43.7 | 0 | 7 mm (0.28 in) |
| Footswitch B | Enclosure face | -40.2 | -34.2 | 12 mm (0.47 in) |
| LED B | Enclosure face | -20.5 | -34.2 | 8 mm (0.31 in) |
| LED A | Enclosure face | 20.5 | -34.2 | 8 mm (0.31 in) |
| Footswitch A | Enclosure face | 40.2 | -34.2 | 12 mm (0.47 in) |
| Output | Top side | -40.8 | 20.2 | 9.5 mm (0.37 in) |
| DC | Top side | 0 | 20.2 | 12 mm (0.47 in) |
| Input | Top side | 40.8 | 20.2 | 9.5 mm (0.37 in) |
| Loop Return | Top side | -20.4 | 20.2 | 11.2 mm (0.44 in) |
| Loop Send | Top side | 20.4 | 20.2 | 11.2 mm (0.44 in) |
Print a drill jig for your own build
The editor turns a layout into a jig for the exact enclosure you picked. It fits snugly, so it stays put while you punch and every mark lands where your layout puts it. It marks the side faces as well, so the jacks and the DC socket are covered.
See the drill jig, $29 →